10% off Stain Proof and Black Jack Eterna-Kote 100% White Silicone Roof Coating
Duralux Marine Paint - Camouflage Collection
Duralux Marine Paint - Camouflage Collection
Regular price
$18.99
Sale price
$18.99
Regular price
Unit price
/per
Adding product to your cart
About this Product
DURALUX CAMOUFLAGE PAINT is a single component/ready to use, ultra low luster flat enamel for use on steel and metal, wood, aluminum or fiberglass. Originally developed for hunting boats, the properties of this product also make it ideal for ATV’s, trailers, tree stands and more. DURALUX CAMOUFLAGE PAINT is salt water resistant, fights rust, resists oil and gasoline, and holds up to the discoloration effects of harbor gases.
Detailed Specifications
Duralux Camouflage Paint is a single package, Ultra low luster enamel for use on steel and metal, wood, aluminum and fiberglass.
Usage Instructions
SURFACE PREPARATION
All surfaces must be free of moisture, wax, dirt, rust and other foreign matter.
Remove any loose or peeling paint.
Use sandpaper, power brushing or a liquid de-glosser to dull any existing gloss.
Remove all dust by wiping surfaces with a clean cloth dampened with paint thinner.
New Steel
On clean, rust-free steel apply a prime coat of either ZINC-LIKE PRIMER M739, or SUB TROP RED PRIMER M740.
Bare galvanized metal should be primed with ALUMINUM BOAT GREEN M736.
Rusted Or Painted Steel
Remove all rust, mill scale and dirt by scraping, brushing or sandblasting.
Prime surfaces with either ZINC-LIKE M739, YACHT PRIMER M741 or SUB TROP RED M740.
Where extensive surface preparation is either impractical or impossible, prepare surfaces by Hand Tool Method SSPC-SP-2 and prime with ALUMITHANE M730.
Aluminum
Wipe surface down with white vinegar and prime with either ALUMINUM BOAT PAINT M736 or ZINC-LIKE M739.
Wood
Clean dirt and contaminants from the surface.
Prime bare wood with YACHT PRIMER M741.
Fiberglass
Sand surface until a dull finish is obtained using fine sandpaper or 1/0 steel wool.
Topcoat with two full coats of DURALUX Marine Enamel.
Lead Warning!
If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/ Lead Information Hotline at 1-800-424- LEAD (5323) or log on to www.epa.gov/ lead.
APPLICATION
Apply two thin coats of DURALUX CAMOUFLAGE PAINT on properly prepared surfaces as outlined in our “Surface Preparation” section.
"Feather edge" last brush strokes to insure a smooth finish.
Do not over apply.
Maintain a wet edge to avoid lap marks.
Do not paint in direct sunlight.
Application Temperature, air, surface & material: Minimum 50°F, Maximum 100°F. Relative Humidity: 85% maximum. At least 5°F above dew point.
METHOD OF APPLICATION
Brush, natural bristle.
Roller, short nap 1/4"-3/8" nap or mohair.
Spray: For airless spray use a .013" to .017" orifice with minimum 1,850 psi at tip.
For conventional spray use Graco 700 Gun 217-757 equipment or equivalent, with fluid pressure of 20 lbs. and atomizing pressure of 35-40 lbs.
Thinning: If thinning is desired, use Mineral Spirits or Xylene not to exceed a half pint (8 ounces) per gallon.
CLEAN UP
Immediately after use with mineral spirits or VM & P Naphtha.
Refer to Safety Data Sheet for additional health and safety information.
Refer to Technical Data Pages for specific surface preparation, application, drying and further information.
*disclaimer: on-screen color representations may vary from actual paint colors.
Duralux Camouflage Paint is a single package, Ultra low luster enamel for use on steel and metal, wood, aluminum and fiberglass.
SURFACE PREPARATION
All surfaces must be free of moisture, wax, dirt, rust and other foreign matter.
Remove any loose or peeling paint.
Use sandpaper, power brushing or a liquid de-glosser to dull any existing gloss.
Remove all dust by wiping surfaces with a clean cloth dampened with paint thinner.
New Steel
On clean, rust-free steel apply a prime coat of either ZINC-LIKE PRIMER M739, or SUB TROP RED PRIMER M740.
Bare galvanized metal should be primed with ALUMINUM BOAT GREEN M736.
Rusted Or Painted Steel
Remove all rust, mill scale and dirt by scraping, brushing or sandblasting.
Prime surfaces with either ZINC-LIKE M739, YACHT PRIMER M741 or SUB TROP RED M740.
Where extensive surface preparation is either impractical or impossible, prepare surfaces by Hand Tool Method SSPC-SP-2 and prime with ALUMITHANE M730.
Aluminum
Wipe surface down with white vinegar and prime with either ALUMINUM BOAT PAINT M736 or ZINC-LIKE M739.
Wood
Clean dirt and contaminants from the surface.
Prime bare wood with YACHT PRIMER M741.
Fiberglass
Sand surface until a dull finish is obtained using fine sandpaper or 1/0 steel wool.
Topcoat with two full coats of DURALUX Marine Enamel.
Lead Warning!
If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/ Lead Information Hotline at 1-800-424- LEAD (5323) or log on to www.epa.gov/ lead.
APPLICATION
Apply two thin coats of DURALUX CAMOUFLAGE PAINT on properly prepared surfaces as outlined in our “Surface Preparation” section.
"Feather edge" last brush strokes to insure a smooth finish.
Do not over apply.
Maintain a wet edge to avoid lap marks.
Do not paint in direct sunlight.
Application Temperature, air, surface & material: Minimum 50°F, Maximum 100°F. Relative Humidity: 85% maximum. At least 5°F above dew point.
METHOD OF APPLICATION
Brush, natural bristle.
Roller, short nap 1/4"-3/8" nap or mohair.
Spray: For airless spray use a .013" to .017" orifice with minimum 1,850 psi at tip.
For conventional spray use Graco 700 Gun 217-757 equipment or equivalent, with fluid pressure of 20 lbs. and atomizing pressure of 35-40 lbs.
Thinning: If thinning is desired, use Mineral Spirits or Xylene not to exceed a half pint (8 ounces) per gallon.
CLEAN UP
Immediately after use with mineral spirits or VM & P Naphtha.
Refer to Safety Data Sheet for additional health and safety information.
Refer to Technical Data Pages for specific surface preparation, application, drying and further information.
*disclaimer: on-screen color representations may vary from actual paint colors.
